How to troubleshoot cooling system issues on a 1968 Ford Mustang GT Fastback (Bullitt)?

Troubleshooting the cooling system on a classic 1968 Ford Mustang GT Fastback, commonly known as the Bullitt Mustang, is essential to ensure the engine runs smoothly and avoids overheating. Symptoms …

How to troubleshoot cooling system issues on a 1968 Ford Mustang GT Fastback (Bullitt)?

Troubleshooting the cooling system on a classic 1968 Ford Mustang GT Fastback, commonly known as the Bullitt Mustang, is essential to ensure the engine runs smoothly and avoids overheating. Symptoms of a cooling system issue may include the temperature gauge reading higher than normal, visible leaks, steam from the engine bay, or unusual noises. Efficiently solving this issue not only preserves the vehicle's performance but also maintains its value. Here is how to solve this issue:

Join the AutoFame community. Become a member for free, add your car to the garage and tell its story. Join AutoFame.

Step 1: Check the Coolant Level

First, ensure your engine is cold to avoid burns. Locate the radiator cap on the top center of the radiator, identifiable by its metal construction and safety warnings. Slowly remove the cap by pressing down and turning counterclockwise. Verify that the coolant level is at the top. If it's low, fill it with a 50/50 mix of coolant and distilled water. Inspect the overflow tank as well, typically a semi-transparent plastic container situated near the radiator.

Step 2: Inspect for Leaks

Look for visible signs of coolant leaks under the car and around the engine bay. Examine the radiator and hoses. Hoses may be mounted on either side of the radiator, connecting to the water pump (front of the engine) and heater core (near the firewall). They should be firm but not brittle. A leak may appear as green, orange, or yellow fluid, depending on the type of coolant.

Step 3: Inspect and Test the Radiator Cap

Examining the radiator cap is crucial since a faulty cap can lead to low pressure and overheating. The radiator cap is the metal cap with safety warnings found on top of the radiator. Check the rubber gasket for signs of cracking or hardening. You can use a radiator cap tester, available at most auto parts stores, to ensure it holds pressure as specified in the car's manual.

Step 4: Test the Thermostat

The thermostat regulates the engine's temperature by controlling coolant flow. It’s typically housed in a metal casing located where the upper radiator hose connects to the engine. Remove the hose and take out the thermostat housing by loosening the bolts. Boil water and use a thermometer to make sure the thermostat opens at the correct temperature (usually around 195°F for most cars).

Step 5: Inspect the Water Pump

The water pump circulates coolant through the engine and radiator. It is generally located at the front of the engine and connected to the lower radiator hose. Check for leaks around the pump or a wobbling pulley connected to it, which indicates failing bearings. Also, listen for a squealing noise while the engine is running, suggesting a faulty water pump.

Step 6: Check the Fan and Fan Clutch

The cooling fan, located between the radiator and the engine, helps draw air through the radiator to cool the coolant. If you have a mechanical fan, ensure the fan clutch (attached to the center of the fan) allows free spinning when the engine is off but not too much. An electric fan should turn on when the engine reaches a high temperature. If it doesn't, verify the fan relay and temperature sensor, typically found near the thermostat housing.

Step 7: Radiator Flush

Have a car with a story like this? Become an AutoFame member and share it with people who love cars as much as you do.

Over time, debris and rust can clog the radiator. Performing a radiator flush helps remove these obstructions. Drain the old coolant by opening the drain valve (petcock) at the bottom of the radiator. Flush with a radiator cleaner following the product's instructions, then refill with a fresh coolant mix.

Step 8: Inspect Belts and Hoses

Belts drive the water pump and sometimes the fan. Inspect the belts for wear and tension. They should be tight but not overly so, with minor flexibility when pressed. Hoses should be free of cracks and bulges. Replace any worn-out belts or hoses to prevent failures.

By following these detailed steps, you can effectively diagnose and fix cooling system issues in your 1968 Ford Mustang GT Fastback (Bullitt), ensuring it runs smoothly and efficiently.

About AutoFame

AutoFame is a home for people who love cars and the stories behind them. Every car on a show field or in a garage has a history: who built it, who saved it, the road trips, the late nights in the shop and the people who helped along the way. AutoFame gives those stories a place to live, so they are not lost when the hood closes or the car changes hands.

Membership is free. Once you join, you can add your car to your own AutoFame garage with photos, specs and the story only you can tell. Restorations, survivors, daily drivers, race cars and family heirlooms all belong here. Other members can find your car, follow its progress and connect with you over the details that matter to car people.

Beyond member garages, AutoFame publishes stories, guides and features on the cars, builders and history that shape car culture. You will find buying and restoration guides, car parts explainers, special editions, the newest models and the classics that started it all. The AutoFame Gallery puts member cars on display for anyone to browse, and the AutoFame YouTube channel adds owner interviews, show highlights and the conversations that happen around a good car.

AutoFame is also built for the people who run car shows. Organizers use it to manage entries and judging, and judges score each car category by category on their phones, with a written guide for every category so nothing gets skipped. After a judged show, owners can see what their car was scored on and how it compared. Shows across the Texas Gulf Coast have run on AutoFame, including the Moody Gardens Car Show in Galveston, Good Grub and Gears, and Keels and Wheels at Lakewood Yacht Club.

AutoFame was founded by Kevin Brady, whose own life in cars began long before he started building tools for the hobby. The idea is simple: the people who love these cars should have one place to share them, learn from each other and keep the stories going.

Whether you own a show winner, a project that is still in pieces or simply love reading about great cars, there is room for you here.

Be part of the AutoFame community. Join free and become a member today.

All storiesFind an event AboutContactPrivacy

© 2026 AutoFame