How to replace the distributor cap on a 1970 Plymouth Hemi 'Cuda?
The distributor cap in a 1970 Plymouth Hemi 'Cuda is a critical component that distributes high voltage from the ignition coil to the spark plugs in the correct firing order. Over time, the cap can w…
Model: 1970 Plymouth Hemi 'Cuda
The distributor cap in a 1970 Plymouth Hemi 'Cuda is a critical component that distributes high voltage from the ignition coil to the spark plugs in the correct firing order. Over time, the cap can wear out, leading to misfires, rough idling, or even a no-start condition. If you're experiencing these symptoms, it might be time to replace the distributor cap. Here is how to solve this issue.
Join the AutoFame community. Become a member for free, add your car to the garage and tell its story. Join AutoFame.
Step 1: Safety First
Before starting any work under the hood, ensure the vehicle is parked on a flat surface and the engine is turned off and cooled down. Disconnect the negative battery terminal to prevent accidental electrical shorts or shocks.
Step 2: Locate the Distributor Cap
Open the hood of your 'Cuda and find the distributor cap. It is usually located at the rear of the engine bay, towards the driver's side. The cap is a rounded plastic cover with several thick wires attached to it, known as spark plug wires.
Step 3: Remove the Spark Plug Wires
Carefully note or mark the position of each spark plug wire. It's crucial to reinstall them in the same order to maintain the engine's firing order. Using a masking tape and a marker can help. Gently twist and pull each wire off the distributor cap terminals.
Step 4: Unscrew the Distributor Cap
The distributor cap is typically held in place by two screws or clips. Using an appropriate screwdriver, unscrew these fasteners and set them aside. Lift the cap off the distributor carefully.
Step 5: Inspect the Rotor
With the cap removed, you'll see the rotor inside. It's a good practice to inspect the rotor for wear and tear while you have easy access. If it looks worn out or corroded, consider replacing it as well.
Step 6: Install the New Distributor Cap
Align the new distributor cap over the distributor, ensuring it sits flush and the screw holes align correctly. Secure it in place by tightening the screws or reattaching the clips you previously removed.
Step 7: Reattach the Spark Plug Wires
Refer to the markings you made earlier and reattach each spark plug wire to the corresponding terminal on the new distributor cap. Push each wire firmly to ensure a good connection.
Step 8: Reconnect the Battery
Reconnect the negative battery terminal.
Step 9: Test the Engine
Start your 'Cuda to ensure the engine runs smoothly and that there are no misfires or rough idling. If everything is running correctly, you have successfully replaced the distributor cap.
By following these steps, you can effectively replace the distributor cap on your 1970 Plymouth Hemi 'Cuda, restoring proper engine performance.
Have a car with a story like this? Become an AutoFame member and share it with people who love cars as much as you do.
About AutoFame
AutoFame is a home for people who love cars and the stories behind them. Every car on a show field or in a garage has a history: who built it, who saved it, the road trips, the late nights in the shop and the people who helped along the way. AutoFame gives those stories a place to live, so they are not lost when the hood closes or the car changes hands.
Membership is free. Once you join, you can add your car to your own AutoFame garage with photos, specs and the story only you can tell. Restorations, survivors, daily drivers, race cars and family heirlooms all belong here. Other members can find your car, follow its progress and connect with you over the details that matter to car people.
Beyond member garages, AutoFame publishes stories, guides and features on the cars, builders and history that shape car culture. You will find buying and restoration guides, car parts explainers, special editions, the newest models and the classics that started it all. The AutoFame Gallery puts member cars on display for anyone to browse, and the AutoFame YouTube channel adds owner interviews, show highlights and the conversations that happen around a good car.
AutoFame is also built for the people who run car shows. Organizers use it to manage entries and judging, and judges score each car category by category on their phones, with a written guide for every category so nothing gets skipped. After a judged show, owners can see what their car was scored on and how it compared. Shows across the Texas Gulf Coast have run on AutoFame, including the Moody Gardens Car Show in Galveston, Good Grub and Gears, and Keels and Wheels at Lakewood Yacht Club.
AutoFame was founded by Kevin Brady, whose own life in cars began long before he started building tools for the hobby. The idea is simple: the people who love these cars should have one place to share them, learn from each other and keep the stories going.
Whether you own a show winner, a project that is still in pieces or simply love reading about great cars, there is room for you here.
Be part of the AutoFame community. Join free and become a member today.