How to replace the distributor cap on a 1967 Shelby GT500?

Replacing the distributor cap on a 1967 Shelby GT500 is an essential maintenance task that can resolve issues related to misfiring, rough idling, or a hard-starting engine. The distributor cap is a k…

How to replace the distributor cap on a 1967 Shelby GT500?

Replacing the distributor cap on a 1967 Shelby GT500 is an essential maintenance task that can resolve issues related to misfiring, rough idling, or a hard-starting engine. The distributor cap is a key component of the ignition system, responsible for routing high-voltage electrical current from the ignition coil to the spark plugs. Over time, it can wear out or get damaged, leading to poor engine performance. Here is how to solve this issue and ensure your Shelby GT500 runs smoothly.

Join the AutoFame community. Become a member for free, add your car to the garage and tell its story. Join AutoFame.

Step 1: Gather the Necessary Tools and Parts

Before beginning, ensure you have the following:

Step 2: Locate the Distributor Cap

The distributor cap is situated in the engine bay. It is generally found towards the rear of the engine, near the firewall, on top of the distributor assembly. The cap is usually a round or semi-circular component with several spark plug wires connected to it.

Step 3: Disconnect the Battery

Safety first! To avoid any electrical shock or accidental sparking, disconnect the negative terminal of the battery. The negative terminal typically has a black cable and is marked with a minus (-) symbol.

Step 4: Remove the Spark Plug Wires

Carefully remove the spark plug wires from the distributor cap. Be sure to note the order in which they are connected. It helps to either take a picture or label them with masking tape so you can replace them correctly later. Gently twist each wire boot and pull it off the terminal to avoid damaging the wires.

Step 5: Remove the Distributor Cap

Locate the screws or clips holding the distributor cap in place. Using your screwdriver, remove these fasteners. Lift off the cap, being careful not to disturb the rotor underneath, which is usually located in the center of the distributor base. The rotor distributes voltage from the ignition coil to the correct spark plug wire.

Step 6: Inspect the Rotor and Interior of the Distributor

With the distributor cap removed, take a moment to inspect the rotor and the interior of the distributor for any signs of wear or buildup of debris. If the rotor shows signs of wear or corrosion, it may also need to be replaced.

Step 7: Install the New Distributor Cap

Place the new distributor cap over the distributor, ensuring it fits snugly over the rotor. Align the cap as per the manufacturer’s specifications, and fasten it with the screws or clips removed earlier. Make sure it is securely in place.

Step 8: Reattach the Spark Plug Wires

Reattach the spark plug wires to the new distributor cap in the exact order they were removed. Ensure that each wire is firmly connected to its respective terminal.

Step 9: Reconnect the Battery

Reconnect the negative terminal of the battery, ensuring it is tightened securely to prevent any electrical issues.

Step 10: Test the Vehicle

Start the engine to check if it runs smoothly. Listen for any irregularities in the engine's operation to ensure the new distributor cap is functioning correctly.

Have a car with a story like this? Become an AutoFame member and share it with people who love cars as much as you do.

By following these steps, you can effectively replace the distributor cap on your 1967 Shelby GT500, potentially solving issues related to ignition and overall engine performance. Regular maintenance of the distributor cap can help ensure that your classic muscle car continues to perform at its best.

About AutoFame

AutoFame is a home for people who love cars and the stories behind them. Every car on a show field or in a garage has a history: who built it, who saved it, the road trips, the late nights in the shop and the people who helped along the way. AutoFame gives those stories a place to live, so they are not lost when the hood closes or the car changes hands.

Membership is free. Once you join, you can add your car to your own AutoFame garage with photos, specs and the story only you can tell. Restorations, survivors, daily drivers, race cars and family heirlooms all belong here. Other members can find your car, follow its progress and connect with you over the details that matter to car people.

Beyond member garages, AutoFame publishes stories, guides and features on the cars, builders and history that shape car culture. You will find buying and restoration guides, car parts explainers, special editions, the newest models and the classics that started it all. The AutoFame Gallery puts member cars on display for anyone to browse, and the AutoFame YouTube channel adds owner interviews, show highlights and the conversations that happen around a good car.

AutoFame is also built for the people who run car shows. Organizers use it to manage entries and judging, and judges score each car category by category on their phones, with a written guide for every category so nothing gets skipped. After a judged show, owners can see what their car was scored on and how it compared. Shows across the Texas Gulf Coast have run on AutoFame, including the Moody Gardens Car Show in Galveston, Good Grub and Gears, and Keels and Wheels at Lakewood Yacht Club.

AutoFame was founded by Kevin Brady, whose own life in cars began long before he started building tools for the hobby. The idea is simple: the people who love these cars should have one place to share them, learn from each other and keep the stories going.

Whether you own a show winner, a project that is still in pieces or simply love reading about great cars, there is room for you here.

Be part of the AutoFame community. Join free and become a member today.

All storiesFind an event AboutContactPrivacy

© 2026 AutoFame