How to replace brake pads on a 2019 Honda Accord?

Tools and Materials Needed Socket set Brake pad spreader/ C-clamp Jack and jack stands Brake fluid New brake pads Torque wrench Rubber mallet Breaker bar Anti-squeal lubricant Wheel chocks Gloves and…

How to replace brake pads on a 2019 Honda Accord?

 

Tools and Materials Needed

 

 

Preparation

 

  1. Park the vehicle on a flat, level surface and set the parking brake to ensure that it does not move during the process.

  2. Place wheel chocks behind the rear wheels for added safety.

  3. Loosen the lug nuts on the wheels but do not fully remove them yet. You'll need the tires to be somewhat secure while you use your breaker bar.

Join the AutoFame community. Become a member for free, add your car to the garage and tell its story. Join AutoFame.

 

Raising the Vehicle

 

  1. Use a jack to lift the front of the car. Consult the owner's manual for recommended jacking points to avoid damaging the vehicle's structure.

  2. Once elevated, place jack stands under the car for added security before lowering the jack slightly so the car rests on the stands.

 

Removing the Wheel

 

  1. Fully remove the lug nuts and carefully take off the wheel, exposing the brake caliper and rotor.

 

Removing the Brake Caliper

 

  1. Locate the brake caliper and use a socket wrench to remove the bolts securing it. These bolts are usually found at the back of the caliper.

  2. Carefully slide the caliper off the rotor. Ensure that you don't let it hang by the brake line as this can cause damage. Secure it with a piece of wire or rest it on the suspension.

 

Removing the Old Brake Pads

 

  1. Slide out the old brake pads from the caliper bracket. Note their orientation to ensure the new pads are installed correctly.

  2. Inspect the caliper bracket and hardware for any visible signs of wear or damage, replacing as necessary.

 

Installing the New Brake Pads

 

  1. Apply a thin layer of anti-squeal lubricant to the backing plate of the new pads. This helps minimize noise when braking.

  2. Position the new brake pads into the caliper bracket in the same way the old pads were oriented.

 

Reassembling the Brake Caliper

 

  1. Before placing the caliper back over the new brake pads, use a brake pad spreader or C-clamp to compress the caliper piston. Be sure to check the brake fluid reservoir, as compressing the piston will cause the fluid level to rise.

  2. Once the piston is compressed, slide the caliper back onto the rotor and secure it with the previously removed bolts. Tighten the bolts to the specified torque settings as outlined in the vehicle’s manual.

 

Reinstalling the Wheel

 

  1. Position the wheel back onto the hub and hand-tighten the lug nuts in a crisscross pattern to ensure even tightening.

  2. Use the torque wrench to securely tighten the lug nuts to the manufacturer's recommended specifications.

 

Lowering the Vehicle and Final Checks

 

  1. Remove the jack stands and slowly lower the vehicle using the jack.

  2. Remove the wheel chocks and double-check that all fasteners are properly tightened.

  3. Start the car and gently pump the brake pedal a few times to ensure the brakes are functioning correctly and set properly against the rotor.

  4. Check the brake fluid reservoir and add fluid if necessary.

Have a car with a story like this? Become an AutoFame member and share it with people who love cars as much as you do.

 

Your brake pad replacement is now complete. Always test the brakes at a low speed in a safe area to ensure proper operation before normal driving.

About AutoFame

AutoFame is a home for people who love cars and the stories behind them. Every car on a show field or in a garage has a history: who built it, who saved it, the road trips, the late nights in the shop and the people who helped along the way. AutoFame gives those stories a place to live, so they are not lost when the hood closes or the car changes hands.

Membership is free. Once you join, you can add your car to your own AutoFame garage with photos, specs and the story only you can tell. Restorations, survivors, daily drivers, race cars and family heirlooms all belong here. Other members can find your car, follow its progress and connect with you over the details that matter to car people.

Beyond member garages, AutoFame publishes stories, guides and features on the cars, builders and history that shape car culture. You will find buying and restoration guides, car parts explainers, special editions, the newest models and the classics that started it all. The AutoFame Gallery puts member cars on display for anyone to browse, and the AutoFame YouTube channel adds owner interviews, show highlights and the conversations that happen around a good car.

AutoFame is also built for the people who run car shows. Organizers use it to manage entries and judging, and judges score each car category by category on their phones, with a written guide for every category so nothing gets skipped. After a judged show, owners can see what their car was scored on and how it compared. Shows across the Texas Gulf Coast have run on AutoFame, including the Moody Gardens Car Show in Galveston, Good Grub and Gears, and Keels and Wheels at Lakewood Yacht Club.

AutoFame was founded by Kevin Brady, whose own life in cars began long before he started building tools for the hobby. The idea is simple: the people who love these cars should have one place to share them, learn from each other and keep the stories going.

Whether you own a show winner, a project that is still in pieces or simply love reading about great cars, there is room for you here.

Be part of the AutoFame community. Join free and become a member today.

All storiesFind an event AboutContactPrivacy

© 2026 AutoFame