How to check and replace brake fluid on a 1967 Shelby GT500?

The brakes are one of the most crucial safety components of any vehicle, and the 1967 Shelby GT500 is no exception. Over time, the brake fluid in your Shelby can become dirty or decrease in level, wh…

How to check and replace brake fluid on a 1967 Shelby GT500?

The brakes are one of the most crucial safety components of any vehicle, and the 1967 Shelby GT500 is no exception. Over time, the brake fluid in your Shelby can become dirty or decrease in level, which can compromise the effectiveness of your braking system. Symptoms of old or low brake fluid include a spongy feeling when pressing the brake pedal, a decrease in braking efficiency, or even warning lights on your dashboard. To ensure your vehicle remains safe and roadworthy, it's important to check and replace the brake fluid. Here is how to solve this issue.

Join the AutoFame community. Become a member for free, add your car to the garage and tell its story. Join AutoFame.

Step 1: Gather Necessary Tools and Materials

Before starting, make sure you have the following items:

Step 2: Locate the Brake Fluid Reservoir

Open the hood of your 1967 Shelby GT500. The brake fluid reservoir is typically located on the driver’s side, near the back of the engine bay, close to the firewall. It is a small, translucent plastic container with a tightly-sealed cap. The cap often has a label on it, specifying “Brake Fluid” and sometimes the type (DOT 3).

Step 3: Inspect the Brake Fluid Level and Condition

Remove the cap from the brake fluid reservoir. Check the fluid level against the “MIN” and “MAX” marks on the side of the reservoir. Also, examine the color of the fluid. Fresh brake fluid is clear or slightly yellow; if it appears dark brown or murky, it needs to be replaced.

Step 4: Remove Old Brake Fluid

Use a turkey baster or a brake fluid syringe to extract the old brake fluid from the reservoir. Place the fluid into a suitable waste container. Be careful not to spill any fluid on your car's paint, as brake fluid can be corrosive.

Step 5: Refill with Fresh Brake Fluid

After removing most of the old fluid, wipe the interior of the reservoir with a clean rag to remove any remaining residue. Pour the new DOT 3 brake fluid into the reservoir, filling it up to the “MAX” line. Be sure to pour carefully to avoid introducing air bubbles into the system.

Step 6: Bleed the Brakes

To ensure there are no air bubbles in the brake lines, you will need to bleed the brakes. Start with the wheel farthest from the master cylinder, usually the rear passenger side, and move inwards. Attach a clear tube to the bleeder valve, place the other end in a container, and have someone press the brake pedal. Open the bleeder valve with a wrench to allow old fluid and air to escape, then close it before releasing the pedal. Repeat this process until only fresh fluid flows through, then move to the next wheel.

Step 7: Check the Brake Pedal Feel and Fluid Level

Once all wheels have been bled, check the feel of the brake pedal. It should feel firm, not spongy. Recheck the brake fluid level in the reservoir and top it off if necessary. Ensure the cap is securely replaced on the reservoir.

Have a car with a story like this? Become an AutoFame member and share it with people who love cars as much as you do.

Step 8: Dispose of Old Brake Fluid Properly

Dispose of the old brake fluid at an approved recycling center or hazardous waste disposal site. Do not pour it down the drain or into the ground.

By following these steps, you will have successfully checked and replaced the brake fluid in your 1967 Shelby GT500, ensuring that your braking system remains in top condition.

About AutoFame

AutoFame is a home for people who love cars and the stories behind them. Every car on a show field or in a garage has a history: who built it, who saved it, the road trips, the late nights in the shop and the people who helped along the way. AutoFame gives those stories a place to live, so they are not lost when the hood closes or the car changes hands.

Membership is free. Once you join, you can add your car to your own AutoFame garage with photos, specs and the story only you can tell. Restorations, survivors, daily drivers, race cars and family heirlooms all belong here. Other members can find your car, follow its progress and connect with you over the details that matter to car people.

Beyond member garages, AutoFame publishes stories, guides and features on the cars, builders and history that shape car culture. You will find buying and restoration guides, car parts explainers, special editions, the newest models and the classics that started it all. The AutoFame Gallery puts member cars on display for anyone to browse, and the AutoFame YouTube channel adds owner interviews, show highlights and the conversations that happen around a good car.

AutoFame is also built for the people who run car shows. Organizers use it to manage entries and judging, and judges score each car category by category on their phones, with a written guide for every category so nothing gets skipped. After a judged show, owners can see what their car was scored on and how it compared. Shows across the Texas Gulf Coast have run on AutoFame, including the Moody Gardens Car Show in Galveston, Good Grub and Gears, and Keels and Wheels at Lakewood Yacht Club.

AutoFame was founded by Kevin Brady, whose own life in cars began long before he started building tools for the hobby. The idea is simple: the people who love these cars should have one place to share them, learn from each other and keep the stories going.

Whether you own a show winner, a project that is still in pieces or simply love reading about great cars, there is room for you here.

Be part of the AutoFame community. Join free and become a member today.

All storiesFind an event AboutContactPrivacy

© 2026 AutoFame