How to adjust the carburetor on a 1968 Ford Mustang GT Fastback (Bullitt)?

If your 1968 Ford Mustang GT Fastback (Bullitt) is experiencing rough idling, poor acceleration, or excessive fuel consumption, it might be time to adjust the carburetor. The carburetor, which contro…

How to adjust the carburetor on a 1968 Ford Mustang GT Fastback (Bullitt)?

If your 1968 Ford Mustang GT Fastback (Bullitt) is experiencing rough idling, poor acceleration, or excessive fuel consumption, it might be time to adjust the carburetor. The carburetor, which controls the mixture of air and fuel entering the engine, can often lose its optimal settings due to wear and age. Ensuring that your carburetor is finely tuned will enhance performance and fuel efficiency. Here is how to solve this issue:

Join the AutoFame community. Become a member for free, add your car to the garage and tell its story. Join AutoFame.

Step 1: Preparation

Before you begin, make sure your Mustang is parked on a flat surface and the engine is turned off. Open the hood and locate the carburetor, which is situated on top of the engine, usually capped with an air filter. Remove the air filter to gain clear access to the carburetor.

Step 2: Identify Adjustment Screws

The carburetor will have two main adjustment screws: the idle mixture screws and the idle speed screw. The idle mixture screws typically have springs around their bases and are found on the side of the carburetor. The idle speed screw is often located near the throttle lever of the carburetor.

Step 3: Adjust Idle Mixture Screws

Using a flat-head screwdriver, gently turn the idle mixture screws clockwise until they lightly seat. Be careful not to overtighten, as this could damage the screws. Once both screws are seated, turn them counterclockwise one and a half turns as a starting point. These screws control the air-fuel mixture at idle, so fine-tuning them is crucial for smooth engine performance.

Step 4: Adjust Idle Speed Screw

Locate the idle speed screw, generally found near the throttle lever. Turn this screw clockwise to increase the idle speed and counterclockwise to decrease it. The goal is to set a stable idle speed—typically around 600-700 RPM for a 1968 Mustang GT Fastback. You’ll need a tachometer to measure the engine speed accurately.

Step 5: Warm Up the Engine

Start the engine and let it reach its normal operating temperature. This usually takes around 10-15 minutes. Pay attention to the engine’s response; if it’s sputtering or idling roughly, you may need to readjust the screws slightly.

Step 6: Fine-Tuning

With the engine warm, go back to the idle mixture screws. Turn each screw slowly clockwise and counterclockwise to find the point where the engine runs most smoothly. Adjust each screw gradually; small increments can make significant differences. After optimizing the mixture, recheck the idle speed and adjust the idle speed screw if necessary.

Step 7: Reinstall Air Filter

Once you’re satisfied with the adjustments, turn off the engine and replace the air filter. Ensure it is secured properly to prevent any air leaks that might disrupt the carburetor’s performance.

Step 8: Test Drive

Take your Mustang for a test drive to ensure that the adjustments have improved performance. Pay attention to the idle at stoplights, acceleration, and overall power. If needed, you can perform minor tweaks once you return.

Have a car with a story like this? Become an AutoFame member and share it with people who love cars as much as you do.

By following these detailed steps, you should be able to improve the performance and fuel efficiency of your 1968 Ford Mustang GT Fastback (Bullitt). Regularly checking and adjusting the carburetor can help keep your classic car running smoothly.

About AutoFame

AutoFame is a home for people who love cars and the stories behind them. Every car on a show field or in a garage has a history: who built it, who saved it, the road trips, the late nights in the shop and the people who helped along the way. AutoFame gives those stories a place to live, so they are not lost when the hood closes or the car changes hands.

Membership is free. Once you join, you can add your car to your own AutoFame garage with photos, specs and the story only you can tell. Restorations, survivors, daily drivers, race cars and family heirlooms all belong here. Other members can find your car, follow its progress and connect with you over the details that matter to car people.

Beyond member garages, AutoFame publishes stories, guides and features on the cars, builders and history that shape car culture. You will find buying and restoration guides, car parts explainers, special editions, the newest models and the classics that started it all. The AutoFame Gallery puts member cars on display for anyone to browse, and the AutoFame YouTube channel adds owner interviews, show highlights and the conversations that happen around a good car.

AutoFame is also built for the people who run car shows. Organizers use it to manage entries and judging, and judges score each car category by category on their phones, with a written guide for every category so nothing gets skipped. After a judged show, owners can see what their car was scored on and how it compared. Shows across the Texas Gulf Coast have run on AutoFame, including the Moody Gardens Car Show in Galveston, Good Grub and Gears, and Keels and Wheels at Lakewood Yacht Club.

AutoFame was founded by Kevin Brady, whose own life in cars began long before he started building tools for the hobby. The idea is simple: the people who love these cars should have one place to share them, learn from each other and keep the stories going.

Whether you own a show winner, a project that is still in pieces or simply love reading about great cars, there is room for you here.

Be part of the AutoFame community. Join free and become a member today.

All storiesFind an event AboutContactPrivacy

© 2026 AutoFame